)Step 1: DisassemblyShow All ItemsRemove a single T4 Torx screw from the back of the unit.Step 2: Disassembly, Cont.Show All ItemsSlide the cover toward the mouthpiece.The cover is very tight and may require some force to slip off the unit.Be careful not to loose 2 little bowl magnets as shown in the image.Step 3: Disassembly, Cont.Show All ItemsOnce the cover is off, you will see the internal circuitry and a single battery cell taped to the unit.Step 4: Battery RemovalShow All ItemsCarefully cut the tape, remove it from the battery and slide the battery out of its compartment.Step 5: Disconnecting Battery Show All ItemsSimply rip the weld tabs off the battery.Step 6: Insulation RemovalShow All ItemsUsing a knife, cut and remove the shrink tube insulation from the weld tabs and wires.After shrink tubing is off, the solder joints will be visible.Use a soldering iron to desolder tabs from the wires.Step 7: Prepare the WiresShow All ItemsSlip new shrink tubing over the wires.You can also use electrical tape in the later steps if you don't have shrink tubing.Step 8: Connect New Battery Show All ItemsFor a replacement, I used Panasonic NCR18650B 3400 mAh battery.

This cell had the solder tabs spot welded on in our shop.The tabs are thinner and narrower than standard weld tabs in order to match the original.Solder the wires to the terminal tabs only.Do not solder directly to the battery!!!Step 9: Complete the InsulationShow All ItemsSlide the shrink tubing over the terminal tabs and solder joints leaving as little of the tabs exposed, as possible.Heat them up with a hair dryer or a heat gun to shrink in place.Step 10: Re-assemblyShow All ItemsInsert the battery back into its compartment and replace the tape that was cut during the disassembly, any electrical tape will do.Slide the cover back over the unit, replace the torx screw.Your Pax will not turn on.Don't worry, you just need to "unlock" the internal protection circuit.Simple place your Pax on its charging base and make sure that it is plugged in.Watch that light come to life!Think of the LED on PAX as its health meter.If your PAX LED is blinking green when placed on the charging dock, it may be an indication that some moisture is trapped in the internal components of your PAX.

Sometimes a bit too much isopropyl alcohol or mouthpiece lubricant used during cleaning can cause this, so we always advise that a little goes a long way!vaporizer vpr-007Try this common trick for electronic devices when exposed to moisture: put your PAX in a sealed container of dry white rice for at least 24 hours to absorb any moisture trapped inside PAX.vaporizer taavLeave the oven lid and mouthpiece on the device.v102 vaporizerThe rice serves as a natural desiccant and should draw the moisture out.vaporizer 6th element testIf this remedy proves unsuccessful, or if your PAX LED is showing any other irregular indications while charging, please send the PAX Pros a Support Request for technical help.vaporizer aspire bdc

My PAX LED does not light up on the charger.+ First double-check to see that the cable is plugged in properly to the charge platform and outlet.vaporizer sales onlineIf you have not already, please ensure your device is making a good connection by lightly cleaning the contacts on the device and prongs on the charging base.We recommend using a Q-tip dipped in isopropyl alcohol to clean these areas.Wiggle PAX around a bit on the charger to see if it makes a connection, or try placing it on the platform facing the other way.Also, try charging the device after you've removed the mouthpiece.Test another PAX charger if you have one available.If you continue to have problems charging your PAX, please send the PAX Pros a Support Request.My PAX makes a rattling noise when I shake it.+ There are two components in PAX that will make a bit of noise.The mouthpiece has a small, sliding ring on the metal stem.

This piece needs to freely shake back and forth for the mouthpiece to open and close properly - keep this clean to prevent your mouthpiece from getting jammed with build-up.The other part you'll hear is the internal accelerometer, a loose ball bearing with sensors around it that detects the motion of PAX.When you shake the device to check the battery level, you'll hear the accelerometer making a slight clicking noise.Will my PAX work in extremely cold weather conditions?+ PAX will work in cold weather conditions above freezing temperatures.Keep PAX warm and dry when out and about in cold weather.Your pocket is a great place for PAX.If your PAX has been exposed to extremely cold temperatures for an extended time, try this: Warm it up in your hands before attempting to turn it on.If PAX appears doesn’t turn on immediately, place your device on the charger for a couple minutes and try again.What kind of battery does PAX use?What is the capacity?+ How long will my PAX take to charge and how long will on charge last?

+ PAX is fully charged in two hours.When placed on the charging platform, the PAX LED will shine orange.At 80% battery charge (around 90 min) the LED will shine a steady green.Most PAXers report an average of five oven-loads before needing to recharge their PAX battery.To ensure you always have 100% charge before walking out the door, charge PAX for 2 hours.Do you know how to check your battery levels?Watch these videos Read the digital User Guide.Will I damage my PAX by overcharging?+ What voltage does my PAX battery need for charging?+ Can PAX be charged by USB?+ What should I know about storing PAX for an extended period of time?+ What should I know about battery degradation?+ All batteries degrade over time.As a consumable component in PAX, the Limited 10 Year Warranty does not apply to normal performance degradation of batteries.Fear not, PAX has a plan!PAX’s Battery Service is arranged through and approved by our knowledgeable Tech and Support team, the PAX Pro’s.